Degrees of Customization
Improvements in the availability and economy of Cast Stone can often be achieved when the Specifier balances the needs of a project with the degree of custom shapes needed for the cast stone installation. The indirect labor costs of design, layout, supervision, coordination and mould making needed for a “full custom” project can greatly exceed the actual direct cost of just casting and delivering a basic or standard product to the jobsite. This causes wide variances in the price of Cast Stone and places a premium on the product, which is not always necessary.
With the foregoing in mind, Cast Stone projects will generally fit into one of the following categories: Standard, Semi-Custom or Custom:
Standard Cast Stone items are purchased according to a manufacturers catalog, shop drawing or inventory of moulds. They may be ready made items or made to order. The units are usually priced individually. The architect or contractor determines the quantities and location of each unit on the structure as well as the method of anchoring to the structure, if required. The Cast Stone manufacturer provides no layout drawings. Cutting of units in the field is usually required.
Semi-custom Cast Stone items are purchased according to unit shapes shown on contract documents or according to shop tickets specially prepared to define the scope of the work. They are usually made to order either from custom or inventoried moulds. The units may be priced either individually or as a lump sum contract for the project. The Cast Stone manufacturer prepares shop tickets for approval, which show the quantities, cross section, reinforcement, finished faces, anchoring provisions and a schedule of lengths to be provided. The architect or contractor confirms the quantities, sizes and location of each unit on the structure as well as the method of anchoring to the structure, if required. The Cast Stone manufacturer provides no layout drawings. Some cutting of units in the field may be required.
Custom Cast Stone items are purchased strictly according to contract documents and according to shop drawings specially prepared to confirm the scope of the work. They are usually made to order from custom moulds. The units are usually priced as a lump sum contract for the project, according to plans and specifications. The Cast Stone manufacturer prepares shop drawings for approval, which show the details of stones, arrangement of joints, quantities, cross section, reinforcement, finished faces, anchoring methods, anchors and the location of the units on the structure. The architect and contractor approve the shop drawings to confirm the Cast Stone manufacturers interpretation of the contract documents, quantities, sizes, location of each unit on the structure, method of anchoring to the structure and coordinate the interface of the Cast Stone with other trades. The Cast Stone manufacturer normally provides layout drawings. Cutting of units in the field is usually not required.
In many specifications today, architects are requiring
layout drawings that call for the location of every joint on the building façade to be
precisely located, while others desire standard products and consider custom products to
be cost prohibitive. Methods are available for controlling joint locations when
using semi-custom typical lengths and standard products as described herein and they
should be used whenever possible.
Where jointing layouts are not clearly shown on contract documents or where shop drawing
requirements are not clearly spelled out in the project specifications, misunderstandings
and disappointment can develop between the architect and Cast Stone manufacturer, unless
the parties first agree that the job will be fully custom in nature.
When the architect implements a standard or semi-custom design, which commits to a certain number of shapes and sizes, the approval process is significantly streamlined and delivery times are shortened. The masonry contractor may choose to receive a neat pallet of modular units, which can easily be cut to fit the exact as-built dimensions at the jobsite.
For most installations, typical lengths will be the common unit, with 4’-0” modules (3’-11 5/8”) as the most popular size. Longer lengths are available but should generally not exceed 15 times the minimum cross section thickness. Control joint spacing should divide evenly by the size of the typical unit. Special corner and end units should be cast to suit the end-of-wall condition and intermediate units may be cut with a standard abrasive blade masonry saw.
A typical fitting specification should include the following:
1. Follow architect’s jointing pattern as shown on contract drawings.
2. Cut units to suit in-place wall dimensions.
3. All window and door surrounds shall consist of evenly sized units.
4. Apply zinc primer to all exposed reinforcement before setting stone.
Window sills should be sized to fit the masonry opening or mullion spacing, with allowance for 3/8” joints. The height of all Cast Stone, which is built into masonry walls, should match the brick coursing. Profiles should be designed with the Cast Stone Institute Value Engineering suggestions at hand.
Standard Cast Stone jobs are best suited for designs that call for basic and popular items such as band courses and wall cap coping, pier caps, keystones, quoins and window sill units sized to replace brick. Semi-custom projects can include almost any application where the designer is willing to dimension the stone units on the contract documents.
Custom Cast Stone designs represent the majority of buildings under construction today. Layout drawings are needed for projects that have many different profiles running through changing wall sections or one-of a-kind installations such as entrances, porticos and signs. Base courses of stone at changing grade elevations, radius walls and applications suspended from structural concrete or steel are other good applications for custom Cast Stone.
This Technical Bulletin is provided by the Cast Stone Institute, and is intended for guidance only. Specific details should be obtained from the manufacturer or supplier of the Cast Stone units.
Copyright © 1997-2003 by Cast Stone Institute, Inc. Reproduced with permission by Cast Stone Institute, Inc.